1-11.5 PTF-SAE-SHORT PTF-SAE SHORT Internal Thread Specifications
1-11 1/2 PTF-SAE SHORT
ASMESTD: ASME B1.20.3SOURCE: Table 5 · p. 9TYPE: Internal (nut/tapped hole)CLASS: —SERIES: PTF-SAE SHORTTAPER 1:16
Major diameter
1.2981 – 1.2848
max – min, at the gage plane
Pitch diameter
1.23320 – 1.22505
max – min, at the gage plane
Minor diameter
1.1683 – 1.1567
max – min, at the gage plane
Pitch
0.08696
11.5 threads per inch
Thread profile
Internal profile over three pitches at the gage plane, drawn at maximum material (sharpest crest, flattest root); hatched bands are the truncation zones. Diameters shortened.
Thread length, taper and gage planes
Lengths, taper and gage planes to scale; diameters shortened. D and K at the planes are calculated with the mean truncations.
Limits of size, class —
| Dimension | Basic | Max | Min | Tolerance |
|---|---|---|---|---|
| Major diameter D1Root of the internal thread | 1.2981 | 1.2848 | 0.0133 | |
| Pitch diameter E1Large end, face of the internal thread (E1 short) | 1.2332 | 1.23320 | 1.22505 | 0.00815 |
| Minor diameter K1Crest of the internal thread | 1.1683 | 1.1567 | 0.0116 | |
| Crest truncation fcFig. 2, both threads | 0.0052 | 0.0035 | ||
| Root truncation frFig. 2; at least the mating crest’s maximum | 0.0078 | 0.0052 | ||
| Crest flat FcEquivalent width of flat (Fig. 2) | 0.006 | 0.004 | ||
| Root flat FrEquivalent width of flat (Fig. 2) | 0.009 | 0.006 |
Dimensions in inches. Values are those of the standard (ASME B1.20.3); calculated cells follow the standard’s formulas. Where the standard prints a value that differs from its formula, the printed value is shown with a note.
Diameters along the taper D major, E pitch, K minor (Table A1 notation), inches
| Plane | E basic | E max | E min | D basic | D max | D min | K basic | K max | K min |
|---|---|---|---|---|---|---|---|---|---|
| Plane 1 | 1.23320 | 1.23320 | 1.22505 | 1.2955 | 1.2981 | 1.2848 | 1.1666 | 1.1683 | 1.1567 |
| Plane 0 | 1.21363 | 1.21363 | 1.20548 | 1.2759 | 1.2785 | 1.2652 | 1.1470 | 1.1487 | 1.1372 |
| Plane 3 | 1.19730 | 1.19730 | 1.18915 | 1.2596 | 1.2622 | 1.2489 | 1.1307 | 1.1324 | 1.1208 |
The standard defines no basic major or minor diameter: D basic and K basic are calculated with the mean Fig. 2 truncations. On the taper every diameter changes by 0.0625 in. per inch of length.
Taper, lengths and gaging
Taper, gage and sealing para. 1.6, Fig. 1, Fig. 2
- Taper on the diameter T
- 0.0625 ± 0.0050 in/in
- Half apex angle of the pitch cone β
- 1° 47′ 24″
- Included taper angle 2β
- 3° 34′ 47″
- Taper on the radius
- 0.03125 in/in
- Taper per thread on the diameter
- 0.005435 in
- Gage tolerance, plus / minus ±
- 0 / 1.5 turns
- Gage reference plane
- Large end, face of the internal thread (E1 short)
- PD tolerance basis
- Plus 0, minus 1-1/2 turns of the L1 gage (para. 1.6); L2/L3 gage within ±1/2 turn of the actual L1 position
- Lead angle at the basic PD λ
- 1° 17′
- Crest/root interference at flank contact, min – max δ
- 0.0000 – 0.0043 in
- Recommended mating thread
- NPTF external (primary). Not designed for PTF-SAE SHORT external; at extreme tolerance limits may not assemble with it (Table 1 note 4)
Basic pitch diameters and lengths
- Pitch dia at the small end of the external thread E0
- 1.21363 in
- Pitch dia at the large end of the SAE short internal E1s
- 1.2332 informula gives 1.2332
- Pitch dia at the small end of the internal thread E3
- 1.1973 in
- Hand engagement L1
- 0.3130 · 3.60 in, turns
- Wrench make-up L3
- 0.2609 · 0.01630 in, PD interference
- Full internal thread Lt
- 0.5739 in
- Hole depth for the SAE short tap
- 1.0956 in
- Engagement with a PTF-SAE SHORT external thread Le
- 0.44 in
Notes
- Conforms in all respects to NPTF except that one thread is removed (para. 1.4.1.2): at the small end of the external thread, at the large end of the internal thread. Gage tolerance read as turns of gage engagement: "minus" means fewer turns, i.e. a larger external thread and a smaller internal thread. This reading matches Table 1 notes 3 and 4. Limits at the gage plane are calculated: pitch diameter from the basic PD and the gage tolerance in turns x 0.0625p; major and minor diameters from the pitch-diameter limits, H = 0.866025p and the Fig. 2 truncation limits.
- Rounding only (last digit): Table 5 E1 short: printed 1.23320, formula gives 1.23319 (+0.00001; E1 short = E0 + 0.0625 L1 short (A.2, with E0 of Table 3))
Mates
1-11 1/2 PTF-SAE SHORT takes a thread of the same standard at the same size and pitch. The standard mating external thread is class —. Check the fit with the standard pair →
Working out the mating options…
Different pitch or a different thread family never mate; the fit check runs over both tolerance zones.
Related thread sizes
Same diameter other pitch, and neighbouring sizes
All values for 1-11 1/2 PTF-SAE SHORTevery column of the workbook row
| Designation | 1-11 1/2 PTF-SAE SHORT |
|---|---|
| Alternate designation | 1.3150 OD-11 1/2 PTF-SAE SHORT |
| Threads per inch | 11.5 |
| Thread form | Dryseal 60°, taper 1:16 |
| Series (Table 1) | PTF-SAE SHORT |
| Series name | Dryseal SAE Short Taper Pipe Thread |
| External / internal | Internal |
| Class | — |
| Nominal size | 1 |
| Pitch P (in.) | 0.08695652 |
| Pipe OD D, basic size (in.) | 1.315 |
| Size category | Standard series (para. 1.2) |
| Source table | Table 5 |
| Printed page | 9 |
| Thread type (para. 1.2) | Type 2 |
| Gage (reference) plane for the limits | Large end, face of the internal thread (E1 short) |
| Basic pitch dia at gage plane (in.) | 1.2332 |
| Gage tolerance plus (turns) | 0 |
| Gage tolerance minus (turns) | 1.5 |
| PD tolerance basis | Plus 0, minus 1-1/2 turns of the L1 gage (para. 1.6); L2/L3 gage within ±1/2 turn of the actual L1 position |
| Major dia max, D at gage plane (in.) | 1.2981 |
| Major dia min, D at gage plane (in.) | 1.2848 |
| Major dia tolerance, D (in.) | 0.0133 |
| Pitch dia max, E at gage plane (in.) | 1.23320 |
| Pitch dia min, E at gage plane (in.) | 1.22505 |
| PD tolerance, E (in.) | 0.00815 |
| Minor dia max, K at gage plane (in.) | 1.1683 |
| Minor dia min, K at gage plane (in.) | 1.1567 |
| Minor dia tolerance, K (in.) | 0.0116 |
| Allowance | none (para. 1.3.2) |
| Root radius | not specified; crests and roots may be rounded within the Fig. 2 truncation limits (para. 1.6) |
| Lead variation ± | not given in B1.20.3 (gaging, B1.20.5) |
| Half-angle variation ± | not given in B1.20.3 (gaging, B1.20.5) |
| Lead angle at basic PD (deg) | 1.2858 |
| Lead angle (deg min) | 1° 17′ |
| Stress area | not given in the standard |
| Thread angle (deg) | 60 |
| Flank angle (deg) | 30 |
| Sharp V height H (in.) | 0.075307 |
| H as printed, Fig. 2 (in.) | 0.07531 |
| Thread height h max (in.) | 0.066607 |
| Thread height h min (in.) | 0.062307 |
| Crest truncation min (in.) | 0.0035 |
| Crest truncation max (in.) | 0.0052 |
| Root truncation min (in.) | 0.0052 |
| Root truncation max (in.) | 0.0078 |
| Crest flat min (in.) | 0.004 |
| Crest flat max (in.) | 0.006 |
| Root flat min (in.) | 0.006 |
| Root flat max (in.) | 0.009 |
| Sweep cut: start diameter at gage plane (in.) | 1.1567 |
| Sweep cut: tip diameter at gage plane (in.) | 1.2848 |
| Sweep cut: depth (in.) | 0.06405 |
| Sweep cut: tip flat (in.) | 0.0090 |
| Sweep cut: profile width at start diameter (in.) | 0.08296 |
| Crest flat as modelled (in.) | 0.00400 |
| Sweep cut: taper on diameter (in./in.) | 0.0625 |
| Check against formulas | Rounding only (last digit): Table 5 E1 short: printed 1.23320, formula gives 1.23319 (+0.00001; E1 short = E0 + 0.0625 L1 short (A.2, with E0 of Table 3)) |
| Notes | Conforms in all respects to NPTF except that one thread is removed (para. 1.4.1.2): at the small end of the external thread, at the large end of the internal thread. Gage tolerance read as turns of gage engagement: "minus" means fewer turns, i.e. a larger external thread and a smaller internal thread. This reading matches Table 1 notes 3 and 4. Limits at the gage plane are calculated: pitch diameter from the basic PD and the gage tolerance in turns x 0.0625p; major and minor diameters from the pitch-diameter limits, H = 0.866025p and the Fig. 2 truncation limits. |
| Taper on diameter (in./in.) | 0.0625 |
| Taper tolerance ± (in./in.) | 0.0050 |
| Half apex angle of pitch cone β (deg) | 1.7899 |
| β (deg min sec) | 1° 47′ 24″ |
| Included taper angle 2β (deg) | 3.5798 |
| 2β (deg min sec) | 3° 34′ 47″ |
| Taper on radius (in./in.), 1 in 32 | 0.03125 |
| β min from taper tolerance (deg) | 1.6468 |
| β max from taper tolerance (deg) | 1.9330 |
| Taper per thread on dia, 0.0625p (in.) | 0.005435 |
| E0: PD at small end of external thread (in.) | 1.21363 |
| E1 short: PD at large end of SAE short internal (in.) | 1.2332 |
| E3: PD at small end of internal, L1 + L3 (in.) | 1.1973 |
| Plane 0: distance from small end (ext) or face (int) (in.) | 0.3130 |
| E0 basic: pitch dia at plane 0 (in.) | 1.21363 |
| E0 max (in.) | 1.21363 |
| E0 min (in.) | 1.20548 |
| D0 basic, calculated (in.) | 1.2759 |
| D0 max: major dia at plane 0 (in.) | 1.2785 |
| D0 min (in.) | 1.2652 |
| K0 basic, calculated (in.) | 1.1470 |
| K0 max: minor dia at plane 0 (in.) | 1.1487 |
| K0 min (in.) | 1.1372 |
| Plane 1: distance from small end (ext) or face (int) (in.) | 0.0000 |
| E1 basic: pitch dia at plane 1 (in.) | 1.23320 |
| E1 max (in.) | 1.23320 |
| E1 min (in.) | 1.22505 |
| D1 basic, calculated (in.) | 1.2955 |
| D1 max: major dia at plane 1 (in.) | 1.2981 |
| D1 min (in.) | 1.2848 |
| K1 basic, calculated (in.) | 1.1666 |
| K1 max: minor dia at plane 1 (in.) | 1.1683 |
| K1 min (in.) | 1.1567 |
| Plane 3: distance from small end (ext) or face (int) (in.) | 0.5739 |
| E3 basic: pitch dia at plane 3 (in.) | 1.19730 |
| E3 max (in.) | 1.19730 |
| E3 min (in.) | 1.18915 |
| D3 basic, calculated (in.) | 1.2596 |
| D3 max: major dia at plane 3 (in.) | 1.2622 |
| D3 min (in.) | 1.2489 |
| K3 basic, calculated (in.) | 1.1307 |
| K3 max: minor dia at plane 3 (in.) | 1.1324 |
| K3 min (in.) | 1.1208 |
| Distance x measured from | face (large end) of the internal thread |
| PD change along x (+1 grows, −1 shrinks, 0 straight) | -1 |
| E at x = 0, basic (in.) | 1.23320 |
| Hand engagement L1 (in.) | 0.4 |
| L1 (threads) | 4.6 |
| Hand engagement L1 short (in.) | 0.313 |
| L1 short (threads) | 3.6 |
| Hand-tight engagement of this thread (in.) | 0.3130 |
| Hand-tight engagement (turns) | 3.60 |
| Wrench make-up L3 = 3p (in.) | 0.2609 |
| PD interference from L3 make-up, on dia (in.) | 0.01630 |
| Length of full internal thread (in.) | 0.5739 |
| Full internal thread (threads) | 6.6 |
| Hole depth for SAE short tap (in.) | 1.0956 |
| L2 / L3 gage correlation with L1 ± (turns) | 0.5 |
| Crest/root interference at flank contact, min (radial, in.) | 0.0000 |
| Crest/root interference at flank contact, max (radial, in.) | 0.0043 |
| Table 2: engagement with NPTF external (in.) | 0.53 |
| Table 2: engagement with PTF-SAE SHORT external (in.) | 0.44 |
| Recommended mating thread (Table 1, C.3) | NPTF external (primary). Not designed for PTF-SAE SHORT external; at extreme tolerance limits may not assemble with it (Table 1 note 4) |
| Lookup key | 1-11 1/2 PTF-SAE SHORT | Internal |
Related tools
- Thread standardsEvery ISO and ASME thread series and size, with limits and drawings.
- Thread Spec CalculatorDiameters, tolerances and geometry for ISO metric and unified threads.
- Thread Fit CheckPick a bolt and a nut and see the clearance or interference.
- Twist Drill SizesASME B94.11M drills: sizes, lengths, shanks and tolerances.
- Thread Designation GuideHow to read M10×1.5, 1/4-20 UNC-2A, NPT and more.
- Thread Notations & TermsSymbols and terms of a thread profile, explained.
ASME B1.20.3: Dryseal Pipe Threads, Inch. Source: workbook data (2026-10-10). Confirm against your licensed copy of the standard before use.